•  
  •  
 

Keywords

Engineering strain, martensite, Mild Steel, Oak charcoal, surface hardening

Document Type

Research Paper

Abstract

Carburizing is a process that improves the mechanical properties of low-carbon steel, particularly its surface hardness. Introducing carbon into the steel's surface enhances the creation of a durable and resistant outer layer.  The technique is especially useful for low-carbon steel because it cannot be hardened by quenching and tempering. This work investigates the effects of solid carburizing on the mechanical properties of mild steel. Oak charcoal was used as a carbon source due to its local availability and low cost. The study examined how solid carburization affects the microstructure and mechanical characteristics of mild steel. Mild steel samples were carburized at 830, 880, and 930 °C temperatures for 30, 50, and 75 minutes. These samples underwent Rockwell hardness, impact, and tensile strength testing. The research investigated the influence of the carburization process, carburization temperature, oak charcoal as a carbon source, and soaking period on the mechanical properties of mild steel. It compared the mechanical properties of mild steel before and after carburization. The treated and untreated samples had different ultimate stress values. The untreated specimens had a value of 629 MPa, whereas the hardened specimens had a value of 1030 MPa. The specimens carburized at 930 °C and submerged for 75 minutes displayed the best mechanical characteristics. Oak charcoal is suitable since the research found that it considerably increases mild steel component surface hardness. This technology is cost-effective and efficient, making it a good choice when other carbon sources are scarce or costly.

References

M.A. Bepari, 2.3 Carburizing: A Method of Case Hardening of Steel, Comp. Mater. Finishing, 2 (2017) 71-106. https://doi.org/10.1016/B978-0-12-803581-8.09187-6 F. Idan, O.V. Akimov, K.O. Kostyk, Surface hardening of steel parts, Odes’kyi Politechnichnyi Universytet Pratsi, 1 (2017) 17–23. https://doi.org/10.15276/opu.1.51.2017.04 Y. Suleiman, Original Research Article Effect of Carburization Time and Temperature on the Mechanical Properties of Mild Steel, 3 (2018) 800 – 804. A . Venkatesh, Evaluation and Diffusion Assessment for Surface Hardening Processes, J. Mater. Sci. Eng. 3 (2014). N.K.P. Negara, I.M. Widiyarta, The study on mechanical properties of pack carburized low carbon steel using BaCO 3 as an energizer, IOP Conf .Ser. Mater. Sci .Eng., 673 (2019) 012125. https://doi.org/10.1088/1757-899X/673/1/012125 A. Ihom, G.B. Nyior, M. Ambayin, Surface Hardness Improvement of Mild Carbon Steels using Arecaceae Waste Flower Droppings, J. Sci. Technol., 13 (2012) 133–136. A. Okongwu,V. Paranthaman, Assessment of the efficacy of some carbonate minerals as energizers in pack carburisation of mild steel, nijotech, 11 (1987) 28– 43. Baali, Y. Benarioua, A.E. Mazouz, An Experimental Study of the Influence of Carburizing Treatment Holding Time on the Structure and Hardness of 16NC6 Steel, Eng. Technol. Appl. Sci. Res., 13 (2023) 10478–10482. https://doi.org/10.48084/etasr.5684 Supriyono, Jamasri, holding time effect of pack carburizing on fatigue characteristic of v-notch shaft steel specimens, AIP. Conf . Proc., 1855 ( 2017) 020005. https://doi.org/10.1063/1.4985450 H. Avner., Introduction to physical metallurgy, 2nd Edition, McGraw-Hill Book Company, New York., 1974. D. Kogan, Research of Lakhtin’s school on advanced processes of surface hardening of machine parts and tools, Met. Sci. Heat .Treat., 52 (2010) 195–203. https://doi.org/10.1007/s11041-010-9264-z O. Aramide, S.A. Ibitoye, I.O. Oladele, J.O. Borode, Pack carburization of mild steel, using pulverized bone as carburizer: Optimizing process parameters, Leonardo J. Pract. Technol ., 16 (2010) 1–12. Ohize, Effects of Local Carbonaceous Materials on the Mechanical Properties of Mild Steel, Mater. Sci. Eng., 13 (2009) 107–113. R. Panda, A. M .Mohanty, D.K .Mohanta, Mechanical and Wear Properties of Carburized Low Carbon Steel Samples, Int. J. of Multidisciplinary and Current Research, 2 (2014) 109-112. Darmo, S. Sinarep, R. Soenoko, A study of the pack carburizing quenching treatment with cane molasses cooling medium effect on the wear resistance of low carbon steel, Eastern-European J. Enterprise Technol., 2 (2021) 32–37. https://doi.org/10.15587/1729-4061.2021.228627 Setiawan, A. Dipogusti, Effect of pack carburizing and viscosity of quenching media on AISI 1010 steel, J. Energy, Mech. Mater. Manuf. Eng., 7 (2022) 9-20. https://doi.org/10.22219/jemmme.v7i1.20743

Highlights

This study investigates how carburization temperature and soaking time affect mild steel mechanical properties. Inexpensive, locally produced oak charcoal was utilized as a carbon source. Mild steel cannot be hardened through quenching due to low carbon content.

DOI

10.30684/etj.2024.144383.1630

First Page

699

Last Page

707

Download

Share

COinS